Definite Purpose Motors
Adjustable Speed Drive Motors
This ASD Ultra technology is optimized for performance in metal processing, plastic extrusion, winders, test stands, crane and hoist and material handling. All are applications that require motors that can handle variable torque applications.
Five-year warranty comes standard. This comprehensive warranty program covers both mechanical and NEMA Premium efficiency performance (60 months operational/66 months maximum from shipment).
Designed for scalar or vector drive
Infinite:1 constant torque from zero to base speed
NEMA Premium efficiency at 60 Hz sinewave
Constant horsepower 1.5 times base speed
Runs at or below Class F temperature rise
Exceeds MG1-31 standards with GEGARD insulation system
1.5-300 HP, 1800 RPM
230/460, 460, 575V / 60 Hz
TEFC, TEBC, TENV (IP55)
Frame sizes: 143TC-449T
NEMA, IEEE 841, IEEE 112B
Oil Well Pump Motors
Wolong oil well pump motors are designed with high slip (5-8%) and high torque (NEMA D) to meet the requirements of oil beam pumping units. With minimal maintenance and stock availability, these motors have become an obvious choice for operators.
Rugged cast iron frame
Opposite drive end bearing locked for high axial thrust capacity
F2 conduit box position, convertible to F1
3 - 150 HP, 1200 RPM
460V / 60 Hz
Frame sizes: ND213T - ND447T
Fire Pump Motors
GEIM is authorized to manufacture fire pump motors per UL File E47088, Vol. 9, Sec. 1 (under Fire Pump QXZF and Inverter Duty PRHJ). A stainless steel embossed nameplate is bolted to each machine.
Fire pump motors sit dormant for many months of the year and may be subject to temperature and barometric changes, especially with outdoor applications. This environment causes condensation to collect on metal surfaces promoting corrosion and leading to unexpected failures. Optional space heaters can be wrapped around the winding coils. They work like an electric blanket transferring a small electric current into heat to keep the motor warm, dry and ready to start when operators need them most.
Class H GEGARD insulation system is designed to excel in severe environments and challenging applications where lesser designs often short circuit and cause overcurrent trips.
GEIM Fire Pump Motors are especially suitable for these applications:
Horizontal Fire Pumps
In-Line Fire Pumps
End Suction Fire Pumps
Vertical Fire Pumps
2, 4, 6 and 8 Pole Designs
Cast Iron TEFC, TENV, ODP, WPI Enclosures
Cast iron bearing cap w/ recessed slinger
Ball bearings standard, Roller Bearings available
1.15 Service Factor limited by UL1004-5
Class B temperature rise (80C)
Continuous Duty (S1)
104F (40C) ambient temperature
3300ft (1000m) altitude
Stainless steel nameplates
Special voltages available
Special shaft designs available
Space heaters, Thermistor, thermostats, or RTD’s available
Shaft grounding rings available
Mill Duty DC Motors
This low base speed, high torque motor is used in high performance, automatic control systems that require a fast-transient response. These motors are ideal for use in steel plants, excavating equipment, shipyard cranes, coal and ore dock cranes. They operate well in constant potential or adjustable voltage drive systems with either rectified power supplies or motor-generator sets.
MD800 motors meet standards established by the Association of Iron and Steel Technology (AIST).
Heavy-duty, double tapered shaft is removable and replaceable.
Single width cylindrical roller bearings for high intermittent and impact thrust capacity.
TIG welding of the armature coil leads to the commutator makes the motor highly resistant to overloads.
Fast dynamic response and smooth speed control due to optimal system inertia.
Advanced Tape-Reinforced Encapsulated Construction (TREC) coil technology is highly resistant to contamination, vibration, impact and wear.
Specifically designed to accelerate, decelerate, or reverse under conditions of severe duty-cycle operation.
Optimal Class H insulation protection is standard.